Mitutoyo Laser Scan Micrometer LSM-6902H - 544-499A
Brand: Mitutoyo- SKU:
- 544-499A
- ID:
- 336758
$12,200.00
Mitutoyo Laser Scan Micrometer LSM-6902H
544-499A
Non-contact, high-accuracy measurement system
Best-in-Class Repeatability of ±0.045μm
Features:
- The best repeatability available in the 25mm/1" class.
- The ultra-precise scanning motor enables the highest measurement accuracy.
- Thanks to excellent linearity, an accuracy of ±0.5μm over the entire measuring rangeand a higher accuracy of ±(0.3+0.1ΔD)µm over a narrow range are guaranteed.
- An excellent option for measuring pin gages or plug gages.
Specifications:
| Measuring Unit | |
| Measuring range | 0.1 to 25mm (0.004 - 1.0 in) |
| Resolution | 0.01 to 10μm (selectable) (0.000001 - 0.0005 in) |
| Repeatability *1 | Whole range: ±0.045μm (±0.0000018 in) (ø25mm) Narrow range: ±0.03μm (±0.0000012 in) (ø10mm) |
| Accuracy *2 (20ºC) | Whole range: ±0.5μm (±0.000020 in) |
| Narrow range: ±(0.3+0.1ΔD) [D:mm]µm ±(.000012+.0001ΔD) [D:inch] *5 | |
| Movement error *3 | ±0.5μm (±.000020") |
| Measuring region *4 | ±1.5mm x 25mm (±.06 x 1.0 in) |
| Scanning rate | 1600 scans/s |
| Laser wavelength | 650nm (visible) |
| Laser scanning speed | 112m/s |
| Operating environment | Temperature: 0 to 40ºC Humidity: RH 35 to 85% (non-condensing) |
*1: At the 2σ level in the case where ø25mm and ø10mm diameters are measured using a measurement time of 1.28 seconds (2048 scans on average)
*2: The value at the center of the measuring range
*3: The additional error (in outside diameter) caused by workpiece movement within the measuring envelope during the measuring cycle
*4: Length along optical axis × Scanning length (Measuring range)
*5: ΔD is the difference in outside diameter between the master gage and workpiece.
| Display Unit | |
| Display | 16-digit plus 11-digit fluorescent display, and guide message LED |
| Segment | 1 to 7 (1 to 3, transparent) or 1 to 255 edges |
| Averaging times | Arithmetic average: 1 to 2048 scans. Moving average: 32 to 2048 scans. |
| Judgment | Selection from "target value + tolerance", "lower tolerance + upper tolerance", or "7 classes multilimit tolerance zone" |
| Measurement mode | Standby, Single measurement, Continuous measurement |
| Statistical analysis | Maximum, Minimum, Max-Min, Average, Dispersion, (S.D) |
| External dimensions | 335mm (W) x 134mm (H) x 250mm (D) |
| Power supply | 100 to 240VAC ±10% 35W 50/60Hz |
| Standard output | RS-232C, Analog I/O |
| Optional output | Digimatic code output unit (2-ch), 2nd I/O analog I/F, BCD I/F |
| Operating environment | 0 to 40°C, RH 35 to 85% (non-condensing) |
| Others | Nominal setting, sample setting, suppression of unnecessary digits, transparent object measurement, automatic measurement in edge mode, output timer, abnormal data elimination, SHL change, group judgment, simultaneous measurement, statistical processing, mastering, buzzer function, automatic workpiece detection (dimension/position), zero-set/offset. Note: In the case of dual measuring-unit connection, extra-fine line measurement and some of the communication commands are not available. |
For more info, visit www.p65warnings.ca.gov.
