Electra-Kool™ Model 2000 Centrifugal Blower

Electra-Kool™ Model 2000 Centrifugal Blower

The two biggest Electra-Kool™ models are too large for most electrical cabinets, but are ideal for cooling large DC motors. Models 2000 CFM blower & 3000 CFM blower force thousands of cubic feet of filtered air per minute into your DC motors, keeping them clean and cool. Electra-Kool™ is low-cost insurance against motor malfunction due to excessive heat. You’ll save a boat load of money in preventative maintenance costs.

ELECTRA-KOOL™ 2000 CFM BLOWER FEATURES:

• 2000 CFM of air flow.
• Recommended capacity: 400 HP DC motor
• 36” height, 14.5” deep, 16” wide
• Rugged cast aluminum housing
• Heavy-Duty Steel Impeller
• 9” square flange (rounded corners, 6.5” hole to hole) that mounts easily
• Long lasting filter life due to huge surface area… 90 SQ FT!
• Simple assembly! Filters require just one wingnut – great for quick cleaning
• Finger-guards installed on both the inlet and outlet for your safety
• One year manufacturing warranty – just in case.

Electra-Kool Filtered Blowers are a low-cost alternative to both air conditioners and compressed air systems. By delivering clean, filtered ambient air to your electrical enclosure, Electra-Kool blowers prevent factory down-time at a fraction of the cost.

Electra-Kool blowers have reliably kept electrical equipment clean and cool since their launch. Trusted by industrial customers everywhere and always in stock.

Electra-Kool Features:

• Simple "bolt-on" design. Secured easily with nuts and bolts. Filters are also easily swapped out with a simple wing-nut.
• High-Efficiency motors made in the USA - lower your operating costs significantly.
• Prevents microscopic dust particles from damaging your electrical components with our pleated paper filters (99.9% efficiency @ 0.5 Microns) or HEPA filters (99.97% @ 0.3 Microns).
• Pre-filter wraps that extend the life of the primary filter
• Mesh finger-guards on both the intake and outlet - Safety First.

Accessories & Options:

• All Electra-Kool blower systems come with louvered vents for hot air release, a thermometer for internal temperature monitoring, and an air deflector plate to direct air toward a hot spot.
• Polyester (medium filtration) or metal mesh (coarse filtration) filters also available.
• FilterKits are available for adding our filters to filterless blowers, Electra-Kool or other.

MODEL 2000 MOTOR SPECIFICATIONS:

• Three Phase Only
• 5 HP, 3450 RPM, 184TC Frame
• 208-230/460V, 60Hz TEFC
• Amps: 12.0 @ 208V, 11.8 @ 230V, 5.9 @ 460V
• UR, CSA, & EEV Listed

View the Model 2000 Cut Sheet

MODEL 2000 FILTER SPECIFICATIONS:

Pleated Paper Filter (Fine filtration)

• Rated for 99.9% efficiency @ 0.5 microns nominal and 99.97% @ 1 micron nominal
• Moisture & oil resistant for consistent performance in all climates
• Filters out dust too small to see with the naked eye

Metal Mesh filter (Coarse filtration)

• Rated 60% @ AC Fine Dust
• Four layers of corrugated aluminum mesh
• Long-lasting, corrosion resistant protection against coarse particulates

Prefilter Wraps

• PREFILTERS are a low-cost filter wrap that extends the life of the main filter.
• Provided along with Blowers with Pleated Paper or HEPA filters
• 1/2" thick, non-woven polyester to pick up larger particles and extend the life of the main filter
• Can be used as a coalescer to help prevent oil mist from entering filter
• Double-wrapping can be more effective.

IMPELLER REPLACEMENT KITS:

• Impeller (also called a Squirrel Cage) Replacement Kits are always in stock for those rare emergencies when your impeller needs to be replaced.