Electra-Kool™ Model 1400 Centrifugal Blower

Electra-Kool™ Model 1400 Centrifugal Blower

An Electra-Kool™ centrifugal fan is the perfect solution for cooling & ventilating your electrical cabinet, DC motor, or other industrial area while keeping fine dust and dirt out. Prevent internal components and electrical enclosures from malfunctioning due to excessive heat or dust. Electra-Kool™ is a fraction of the price of an air conditioner and or compressed air device, saving you both operating and maintenance costs for years.

Electra-Kool Filtered Blowers are a low-cost alternative to both air conditioners and compressed air systems. By delivering clean, filtered ambient air to your electrical enclosure, Electra-Kool blowers prevent factory down-time at a fraction of the cost.

Electra-Kool blowers have reliably kept electrical equipment clean and cool since their launch. Trusted by industrial customers everywhere and always in stock.

Electra-Kool Features:

• Simple "bolt-on" design. Secured easily with nuts and bolts. Filters are also easily swapped out with a simple wing-nut.
• High-Efficiency motors made in the USA - lower your operating costs significantly.
• Prevents microscopic dust particles from damaging your electrical components with our pleated paper filters (99.9% efficiency @ 0.5 Microns) or HEPA filters (99.97% @ 0.3 Microns).
• Pre-filter wraps that extend the life of the primary filter
• Mesh finger-guards on both the intake and outlet - Safety First.

Accessories & Options:

• All Electra-Kool blower systems come with louvered vents for hot air release, a thermometer for internal temperature monitoring, and an air deflector plate to direct air toward a hot spot.
• Polyester (medium filtration) or metal mesh (coarse filtration) filters also available.
• FilterKits are available for adding our filters to filterless blowers, Electra-Kool or other.

ELECTRA-KOOL™ 1400 CFM CENTRIFUGAL FAN FEATURES:

• Enclosures 500-600 Cubic Feet
• Draws 3.0/1.5 Amps
• 1400-1425 CFM of air flow.
• Recommended capacity: 650 cubic foot enclosure OR 250 HP DC motor
• 25.5" height, 14.5" deep, 16" wide
• Rugged cast aluminum housing
• Heavy-Duty Steel Impeller
• 9" square flange (rounded corners, 6.5" hole to hole) that mounts easily to the side or top of any enclosure
• Long lasting filter life due to huge surface area… 45 SQ FT!
• Simple assembly: Filters require just one wingnut – great for quick cleaning
• Finger-guards installed on both the inlet and outlet for your safety
• One year manufacturing warranty – just in case.

MODEL 1400 MOTOR SPECIFICATIONS:

• Three Phase Only
• 1 HP, 1750 RPM, 56C Frame
• 208-230/460V, 60Hz TENV
• Amps: 3.1 @ 208V, 3.0 @ 230V, 1.5 @ 460V
• UR & CSA Listed

View the Model 1400 Cut Sheet

MODEL 1400 FILTER SPECIFICATIONS:

Pleated Paper Filter (FINE filtration)

• Rated for 99.9% efficiency @ 0.5 microns nominal and 99.97% @ 1 micron nominal
• Moisture & oil resistant for consistent performance in all climates
• Filters out dust too small to see with the naked eye

Metal Mesh Filter (Coarse filtration)

• Rated 60% @ AC Fine Dust
• Four layers of corrugated aluminum mesh
• Long-lasting, corrosion resistant protection against coarse particulates

Prefilter Wraps

• Provided along with Blowers with Pleated Paper or HEPA filters
• 1/2" thick, non-woven polyester to pick up larger particles and extend the life of the main filter